Sunline Swan NotesPerth rooftop energy, explained

Home / Blog

Pool Pumps on Synergy's Midday Saver: Timer Settings, Running Costs and Solar Matching

9 November 2026 · Sunline Swan Notes editorial team

Rows of solar panels under a partly cloudy sky

Short answer: a pool pump is one of the easiest loads to move into the cheap middle of the day. On Synergy's 2026 Midday Saver plan, six units of pump energy cost about $0.53 between 9am and 3pm at 8.852c per unit, compared with about $1.46 overnight at 24.3431c and about $2.00 on the Home Plan (A1) at 33.2621c. With rooftop solar, a midday pump can run almost free. Reset the timer to run between about 9:30am and 2:30pm and you could save several hundred dollars a year.

Why pool pumps matter

Pumps run for hours every day, often all year. A single-speed pump commonly draws around 0.75 to 1.5 kW, so six hours of running can use 4.5 to 9 units a day. For many Perth homes with a pool, the pump is the largest single daily load after air conditioning and hot water.

Running cost by tariff

For a pump using 6 units a day:

Tariff and time Rate per unit Daily cost Annual cost
Midday Saver, 9am to 3pm 8.8520c $0.53 $194
Midday Saver, 9pm to 9am 24.3431c $1.46 $533
Midday Saver, 3pm to 9pm 55.3253c $3.32 $1,212
Home Plan (A1), any time 33.2621c $2.00 $728

Source for rates: Synergy Standard Electricity Prices and Charges, 1 July 2026.

Many older pool timers were set to run overnight to suit old off-peak tariffs. On Midday Saver, that overnight habit costs about $339 a year more than running at midday.

Matching the pump to solar

If you have solar, running the pump in the middle of the day uses your own generation. Each unit used rather than exported costs you only the 2c DEBS credit you would have earned outside the 3pm to 9pm window. Six units a day is about $0.12 of lost credits, or roughly $44 a year.

The Bureau of Meteorology's average daily solar exposure at Perth Airport is 29.6 MJ/m² in December and 9.3 MJ/m² in June. In summer, almost any system can carry the pump at midday. In winter, a small system may cover only part of it, with the rest drawn from the grid at the cheap 8.852c rate.

Recommended timer settings

Summer (October to March)

  • Run from around 9:30am to 2:30pm
  • Split into two blocks if your pump has a two-program timer, such as 10am to 12pm and 12:30pm to 2:30pm, to avoid overlapping with other big loads

Winter (April to September)

  • Reduce hours; cooler water needs less filtration
  • Keep runs between 10am and 2pm when solar is strongest

Never

  • Run the pump between 3pm and 9pm on Midday Saver unless you have no choice

Variable-speed pumps

Variable-speed pumps can use much less energy than single-speed pumps because energy use rises steeply with speed. Running slower for longer can filter the same volume for less power. If you are replacing a pump, check the energy rating label and compare annual running costs.

Chlorinators and heaters

  • Salt chlorinators usually run with the pump, so the same timer applies
  • Electric heat pump pool heaters can use a lot of energy; heat at midday where possible
  • Solar pool heating uses the pump to circulate water through roof collectors, which naturally suits midday operation

Batteries and pool pumps

It is rarely worth using battery energy for a pool pump. Battery capacity is better kept for the 3pm to 9pm window, when it offsets power at 55.3253c. Run the pump on solar at midday and let the battery charge from any surplus.

Avoid overloading your solar

If you run the pump, dishwasher, dryer and hot water at once, you may exceed solar output and draw some from the grid. That grid energy still costs only 8.852c on Midday Saver, but spreading loads keeps more of it on solar.

Smart plugs and automation

If your pump timer is old or hard to program, an outdoor-rated smart switch installed by an electrician can schedule it from an app. Some solar inverters can also switch loads on when surplus solar is available.

A quick checklist

  1. Check the pump's rated input power on the label.
  2. Note the current timer settings.
  3. Move all running to between 9am and 3pm.
  4. Cut winter hours.
  5. Check the pool chemistry after a week to make sure filtration is still enough.
  6. Review your next bill for the change in off-peak units.

Tariff choice

If the pump is your main load and you have solar, Midday Saver usually suits pool homes, provided the evening peak can be managed. Compare both plans using your interval data before switching.

The overview of residential solar for Perth homes explains how midday output can be matched to loads like pumps. Installers such as Fusion Sun Solar in Perth can help size a system that carries the pump year round, and these practical WA pool energy notes offer more filtration tips.

Frequently asked questions

When should my pool pump run on Midday Saver?

Between 9am and 3pm, ideally 9:30am to 2:30pm.

How much can I save by moving the pump from overnight?

About $339 a year for a pump using 6 units a day.

Should I use my battery for the pool pump?

Usually not; save the battery for the 3pm to 9pm peak.

Is a variable-speed pump worth it?

Often yes, because slower running uses much less energy.

Conclusion

Resetting a pool timer takes five minutes and can save hundreds of dollars a year on Midday Saver. Run the pump with the sun and keep it well clear of the evening peak.